DIG V2 support

[direct link]

To configure the EXP/MIDI jack on DIG:

• Press and hold the TAP footswitch while powering up DIG. Once both
  LEDs flash, release the footswitch.
• Turn the MIX knob to select the function of the rear panel’s EXP/MIDI jack. The ON LED will change color to indicate the current status as you turn the knob.
  • Expression Pedal mode: GREEN (default) – Allows continuous control over any of the knobs in any direction with a standard TRS expression pedal.
  • Favorite mode: AMBER – Allows you to recall a Favorite setting using a Strymon MiniSwitch.
  • Tap mode: RED – Allows you to set the master delay time via tap tempo using a Strymon MiniSwitch.
  • MIDI mode: BLUE – Allows for the selection of three presets using a Strymon MultiSwitch Plus. Full MIDI functionality is also available by sending MIDI Program Change messages via 1/4″ TRS MIDI connection using a Strymon Conduit or MIDI EXP cable. Up to 300 presets are available via MIDI.
• Press either footswitch to store the EXP/MIDI jack mode and begin using DIG.

[direct link]

To set the Input Level on DIG:

• Press and hold the ON footswitch while powering up DIG.  Once both LEDs flash, release the footswitch.
• Turn the TIME knob to select the Input Level mode.  Both LEDs will change color to indicate the current status as you turn the knob.
  • Instrument: GREEN (default) – Input headroom is set for an instrument level source, such as a guitar or a bass.
  • Line: RED – Input level is set for a line level source, such as a keyboard or synthesizer. 10dB of headroom is added.
• Press either footswitch to store the Input Level setting and begin using DIG.

[direct link]

From the factory, DIG’s bypass mode is set to True Bypass with the option to be set to Buffered Bypass.  There are several benefits to setting DIG to Buffered Bypass mode:

• Preserves the high frequency response of your guitar signal through your pedal chain and long cable runs.
• Helps maintain signal levels when  the pedal is both bypassed and engaged when there is an impedance mismatch between the pedals’ output and the device it is connected to.
• If there is DC offset in the audio signal, it helps eliminate popping in the audio when engaging and bypassing the pedal.

To change the bypass mode on DIG:

• Press and hold the ON footswitch while powering up DIG.  Once both LEDs flash, release the footswitch.
• Turn the MIX knob to choose between True Bypass or Buffered Bypass modes.  The ON LED will change color to indicate the current status as you turn the knob.
  • True Bypass: GREEN (default).
  • Buffered Bypass: RED
• Press either footswitch to store the Bypass mode and begin using DIG.

NOTE:  Connecting a cable into the RIGHT OUTPUT jack will automatically set the bypass mode to Buffered Bypass.

[direct link]

Holding down the TAP footswitch enables Circular Repeats, where both delay lines maintain a static volume and repeat continuously until the TAP footswitch is disengaged.  Circular Repeats can also be engaged with a connected TAP footswitch when the EXP/MIDI jack is set to TAP mode.

[direct link]

To begin using DIG with an external MIDI device, connect the MIDI out jack from a pedal, controller, or computer interface to the EXP/MIDI jack on DIG. The following devices can be used to send MIDI messages to DIG:

• Strymon MIDI EXP cable
• Strymon Conduit MIDI Hub or a compatible 5-pin MIDI to 1⁄4” TRS MIDI Interface
• Connect DIG via USB to a USB host device (such as a computer) that sends MIDI

Set MIDI Output Mode

The MIDI Output mode must be set to determine what kind of MIDI data is sent out by DIG.  ***NOTE: If you are only sending MIDI data to DIG or if you are using the Strymon MIDI EXP cable, the MIDI Output mode must be set to OFF.***

• Press and hold down the TAP footswitch while connecting the pedal to power.
• When the LEDs stop blinking, release the footswitch and turn the TONE knob to select what kind of MIDI data is sent from DIG to other MIDI devices. Both LEDs will flash momentarily to indicate status.
  • RED – OFF (default) – No MIDI messages are sent out of DIG.
  • BLUE – THROUGH – Incoming MIDI messages are sent to the MIDI OUT without any additional MIDI messages generated by DIG.
  • WHITE – SEND CC, PC, OTHER – MIDI CC PC, and Sysex messages generated by DIG.
  • GREEN – SEND CC, OTHER – MIDI CC and Sysex messags generated by DIG are sent to the MIDI OUT.
  • PURPLE – SEND PC, OTHER – MIDI PC and Sysex messages generated by DIG are sent to the MIDI OUT.
  • AMBER – SEND OTHER – Sysex messages generated by DIG are sent to the MIDI OUT.

MIDI Clock Sync

Once you have configured DIG to communicate via MIDI, you can set the pedal to synchronize to incoming MIDI clock.

When DIG is synced to MIDI clock, the echo repeats are synced to the incoming MIDI clock messages.

To set whether DIG will respond to incoming MIDI clock:

1. Press and hold the ON footswitch.  Once both LEDs flash, release the footswitch.
2. Set the position of the TYPE switch to select whether DIG will sync to incoming MIDI Clock messages.  Both LEDs will momentarily change color to indicate the current status as you set the switch.
   • Set the switch down to 12 bit for Off (default): both LEDs light RED – DIG will not respond to MIDI Clock.
   • Set the switch up to 24/96 for On: both LEDs light BLUE – DIG will respond to MIDI Clock.
3. Press either footswitch to store the MIDI Clock setting.

The MIDI Clock setting is saved per Favorite setting or MIDI preset.

Saving and Recalling Presets on DIG with MIDI

Saving Presets via MIDI

***NOTE: Saved Favorite or MIDI presets on DIG will store the settings of all the knobs and toggle switches on the pedal as well as the bypass state of the pedal.***

With the EXP/MIDI jack set to MIDI mode, the currently loaded settings can be saved to any of DIG’s 300 preset locations at any time.

• To enter Save mode, press and hold BOTH footswitches. Both LEDs will blink GREEN to indicate that DIG is waiting to receive a MIDI Program Change message.

• Send a MIDI Program Change message from your connected MIDI device to DIG.  The LEDs will stop flashing and DIG will save the settings to the preset location that corresponds with the MIDI Program Change message it received.
  • To save the current state of the pedal to the currently loaded preset location, press and hold the TAP footswitch until the LED lights BLUE.

Recalling  Presets

[direct link]

When in MIDI mode, the currently loaded settings can be saved to any of DIG’s 300 preset locations at any time.

• To enter Save mode, press and hold BOTH footswitches. Both LEDs will blink GREEN to indicate that DIG is waiting to receive a MIDI Program Change message.
• To save the current state of the pedal to the currently loaded preset location, press and hold the TAP footswitch until the LED lights BLUE.

Another way to save presets in MIDI mode:

• To save the current state of the pedal to any preset location, send the unit a MIDI Program Change on DIG’s currently selected MIDI channel. For example:
  • Send MIDI Program Change #10 to save the preset to the corresponding memory location on the pedal.
  • To recall this preset, send MIDI Program Change #10 from your MIDI controller or sequencer.

[direct link]

Performing a Factory Reset restores the pedal to its factory default Power-up and secondary functions, and replaces all stored presets with their factory default settings.

• Press and hold the ON footswitch while connecting power to the pedal. Once both LEDs flash, release the footswitch.
• Sweep the TIME 2 knob from 0-100% and back two times. Both LEDs will change colors at the extremes of the knob range and blink RED to indicate when the reset is taking place.
  • TURN 1: AMBER
  • TURN 2: RED
  • TURN 3: AMBER
  • TURN 4: Both LEDs flash RED, DIG resets and restarts.

[direct link]

• Configure the EXP/MIDI jack for Tap mode.

– Press and hold the TAP footswitch while powering up DIG. Once both LEDs flash, release the footswitch.

– Turn the MIX knob until the ON LED turns RED. Press either footswitch to store the setting.

• Connect an external switch with a TRS cable to the EXP/MIDI jack.
• Tap in a tempo in quarter notes to set the delay time for Delay 1.

[direct link]

To configure Dig and MultiSwitch Plus to work with each other:

• Press and hold the TAP footswitch while connecting power to the pedal.Hold until both LEDs stop blinking.

• Turn the TIME knob all the way counter-clockwise to set the MIDI channel to Channel 1. The TAP LED should be GREEN.

• Turn the TONE knob to select any of the following MIDI OUT options (both LEDs will show the following indicated colors):
  • Send MIDI CC, PC, and Other Data: WHITE
  • Send MIDI CC and Other Data: GREEN
  • Send MIDI PC and Other Data: PURPLE
  • Send Other Data: AMBER

• Turn the MIX knob all the way clockwise to set the EXP/MIDI jack to MIDI mode. The ON LED should be BLUE.

• Press either footswitch to exit and store the MIDI channel, the MIDI OUT setting, and the EXP/MIDI jack mode.

• Connect a TRS cable to DIG’s EXP/MIDI jack.

• Press and hold the A footswitch on MultiSwitch Plus while connecting the other end of the TRS cable to any one of the three jacks to set it to Preset mode.

To save a preset on DIG with MultiSwitch Plus:

• Dial in the sound that you would like to save as your preset on DIG.

• Press and hold both footswitches on DIG until both the LEDs blink GREEN.

• Press the A, B, or C footswitch on MultiSwitch Plus to save the current state of the pedal to the desired location.

To select a preset on DIG with MultiSwitch Plus:

• Step on a switch that is not illuminated to recall the corresponding preset.

• Step on an illuminated switch to bypass DIG.